anafranil online
IPB

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> Auto Deburring
pbachert
post Jul 2 2009, 04:44 PM
Post #1


Member
**

Group: Members
Posts: 13
Joined: 28-October 08
Member No.: 2,729



Anyone know how to turn off automatic deburring in SprutCam? It machines in areas where I do not wan't it to go thinking it's removing sharp edges and sometimes it's not. Short of manually changing the code has anyone else delt with this issue? Pete Bachert
Go to the top of the page
 
+Quote Post
Sprut_UK
post Jul 2 2009, 10:09 PM
Post #2


Advanced Member
***

Group: Administrators
Posts: 1,089
Joined: 12-December 07
From: United Kingdom
Member No.: 4



Hi Pete, I'm not sure which function you are referring to as Automatic deburring.........can you give a bit more info, or, provide an example project which shows the problem?
I'm sure we can help to solve the problem with a bit more info.

Dave


--------------------
"Never interrupt your opponent when he is making a mistake..." - Napoleon Bonaparte
www.sprut.co.uk
Go to the top of the page
 
+Quote Post
pbachert
post Jul 6 2009, 01:20 PM
Post #3


Member
**

Group: Members
Posts: 13
Joined: 28-October 08
Member No.: 2,729



QUOTE (Sprut_UK @ Jul 2 2009, 06:09 PM) *
Hi Pete, I'm not sure which function you are referring to as Automatic deburring.........can you give a bit more info, or, provide an example project which shows the problem?
I'm sure we can help to solve the problem with a bit more info.

Dave


Dave, Sprutcam creates a toolpath that goes around the corner instead of straight off the part like it's trying to remove the sharp edges left by the cutter. It does this on waterline and flat land finishing operations. I would like the path to go straight off the part, not around the backside of the part I'm making. For some reason the forum won't let me upload any of my project files I can use an example. Do you have an e-mail address I can send a file to? Pete
Go to the top of the page
 
+Quote Post
Sprut_UK
post Jul 14 2009, 10:20 AM
Post #4


Advanced Member
***

Group: Administrators
Posts: 1,089
Joined: 12-December 07
From: United Kingdom
Member No.: 4



Hi Pete, I apologise for the delay in responding, but I have been on vacation.
You can send your project to daveATsprut.co.uk just replace AT with the appropriate symbol........


--------------------
"Never interrupt your opponent when he is making a mistake..." - Napoleon Bonaparte
www.sprut.co.uk
Go to the top of the page
 
+Quote Post
LRG
post Dec 27 2012, 01:33 PM
Post #5


Newbie
*

Group: Members
Posts: 1
Joined: 25-December 12
Member No.: 3,495



I am having the same issue. I want to side mill a end of a block to clean up extra stock, to bring it to size. The block is square but the tool path is wanting to wrap around the edges of the block. I'd rather see a straight A to B path and retract, rather then having the lead in/out arcs. Am i using a wrong operation?
Attached File(s)
Attached File  vise_clamp2.stc ( 224.87K ) Number of downloads: 4
 
Go to the top of the page
 
+Quote Post
Sprut_UK
post Dec 28 2012, 04:02 PM
Post #6


Advanced Member
***

Group: Administrators
Posts: 1,089
Joined: 12-December 07
From: United Kingdom
Member No.: 4



Hi LRG, and welcome to the SprutCAM forum.

There is a function for solving this problem which can be found under 'Trimming', it's called 'Trim rolls'.

When machining simple 2D parts like this you can very often get a lot better control over the machining process by using 2D strategies.

In the attached modified version of your project I have used '2D Contouring' to machine the part. I haven't applied any speeds / feeds etc.

I hope this gives you some idea's.

Dave



Attached File(s)
Attached File  vise_clamp2_dpmod.stc ( 207.29K ) Number of downloads: 3
 


--------------------
"Never interrupt your opponent when he is making a mistake..." - Napoleon Bonaparte
www.sprut.co.uk
Go to the top of the page
 
+Quote Post
Nelly_SC
post Jan 20 2017, 02:14 PM
Post #7


Newbie
*

Group: Members
Posts: 1
Joined: 20-January 17
Member No.: 4,027



I know that's the old topic, but here's the video according to it.
https://youtu.be/bssbgMG0g10

Off-line programming for deburring parts in SprutCAM Robot for FANUC M710 robot.
https://youtu.be/blHfC-QTL6M
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 20th November 2017 - 09:18 PM